Product Overview
The Bently Nevada 330104-00-20-10-02-00 3300 XL 8 mm Proximity Probe is a premium-grade non-contact position and vibration sensor used in high-value rotating equipment monitoring applications. Part sur the world-renowned 3300 XL series, this probe employs proven eddy current technology to deliver precise measurements sur shaft dynamic behavior and axial position.
This particular model features a 1 meter length, non-armored cable, and is optimized for ease sur installation and long-term reliable operation, even in harsh industrial conditions. It works in tandem with 3300 XL extension cables and Proximitor sensors to provide a linear voltage output proportional to the shaft’s distance from the probe tip.
Designed for use in machine protection systems across industries such as oil & gas, power generation, refining, and heavy industry, the 330104-00-20-10-02-00 supports operators with accurate and timely diagnostics, enabling better decisions for maintenance and asset protection.
Spécifications du produit
| Parameter | Specification |
|---|---|
| Modèle | 330104-00-20-10-02-00 |
| Product Type | 3300 XL 8 mm Proximity Probe |
| Sensing Technology | Eddy current, non-contact |
| Probe Tip Diameter | 8 mm |
| Probe Tip Material | Polyphenylene sulfide (PPS) |
| Thread Size | 3/8-24 UNF |
| Total Length | 1 meter |
| Cable Armor | Non-armored |
| Connector Type | Miniature coaxial connector |
| Target Material | 4140 steel (calibrated) |
| Measurement Range | 2 mm (80 mils), linear range |
| Scale Factor | 200 mV/mil (7.87 mV/μm) nominal |
| System Linear Range | 80 mils (2.0 mm) |
| Non-Linearity | ≤ ±0.75% sur full scale (typical) |
| Frequency Response | 0 Hz to 10 kHz (±3 dB) |
| Operating Temperature (Probe) | -51 °C to +177 °C |
| Operating Temperature (System) | -35 °C to +120 °C |
| Humidity | 100% condensing, sealed |
| Shock / Vibration Tolerance | 10 g @ 10-2,000 Hz |
| Pressure Rating | 5 bar (sealed probe tip) |
| Certifications | CE, ATEX Zone 2, CSA, IECEx |
| Poids | 0.323 kg |
Applications
The 330104-00-20-10-02-00 Proximity Probe is deployed worldwide in industries requiring high-reliability shaft position and vibration monitoring:
-
Gas and Steam Turbines
Monitoring rotor axial position and shaft vibration for trip protection and predictive maintenance. -
Centrifugal Compressors
Providing insight into rotor dynamics and early fault detection. -
Electric Motors
Tracking balance, alignment, and bearing health to prevent catastrophic failures. -
Industrial Pumps
Monitoring critical pump shafts in chemical processing, refineries, and utilities. -
Fans and Blowers
Ensuring operational stability and preventing excessive vibration. -
Gearboxes
Supporting detection sur misalignment and gear mesh wear. -
Paper Mills, Steel Plants, Marine Engines
Broad applications across heavy process industries.
Product Advantages
-
World-Class Reliability
Built on Bently Nevada’s globally trusted 3300 XL platform — the most widely used proximity transducer system in the world. -
High-Temperature Performance
Probe rated up to 177 °C for operation in the hottest machinery conditions. -
Accurate, Stable Output
Exceptional linearity and minimal drift over long service life. -
Non-Armored Flexibility
Easier routing and lighter weight for installations where cable protection is not required. -
Certified for Harsh Environments
Meets CE, ATEX Zone 2, CSA, and IECEx certifications for hazardous industrial settings. -
Sealed Against Moisture
100% condensing humidity rated. -
Industry Standard Compatibility
Fully compatible with 3300 XL Proximitor sensors and extension cables. -
Low Maintenance Requirements
Factory-calibrated for long-term use without recalibration. -
Trusted by Leading Operators
Installed globally in thousands sur turbine, compressor, and motor systems.
Questions fréquentes (FAQ)
-
What is the typical application for this probe?
Shaft position and vibration monitoring for turbines, compressors, motors, pumps, and gearboxes. -
What is the key difference between armored and non-armored cable?
Armored cables surfer additional mechanical protection, while non-armored cables provide easier routing in clean environments. -
What is the cable length sur this model?
0.323 kg. -
Is this probe certified for hazardous locations?
Yes — CE, ATEX Zone 2, CSA, IECEx certified. -
What is the recommended target material?
4140 steel or equivalent for factory calibration. -
Is recalibration needed over time?
No — designed for long service life without recalibration. -
How is vibration measured?
By detecting shaft movement relative to the probe tip through eddy current response. -
What is the linear range?
80 mils (2.0 mm). -
What is the operating temperature rating?
Probe: -51 °C to +177 °C. -
Is this model backward compatible with older Bently Nevada systems?
Yes — compatible with many existing 3300 series Proximitor modules.
Related Modèles from the Same Series or Catégorie
| Modèle | Product Type | Cable Length | Armor Type | Dimensions & Poids |
|---|---|---|---|---|
| 330104-00-20-10-02-00 | 3300 XL 8 mm Probe | 20 ft (6.10 m) | Non-armored | 8 mm tip, ~0.55 kg |
| 330104-00-15-10-01-CN | 3300 XL 8 mm Probe | 15 ft (4.57 m) | Non-armored | 8 mm tip, ~0.5 kg |
| 330104-00-25-05-02-00 | 3300 XL 8 mm Probe | 25 ft (7.62 m) | Armored | 8 mm tip, ~0.65 kg |
| 330104-00-10-10-01-CN | 3300 XL 8 mm Probe | 10 ft (3.05 m) | Non-armored | 8 mm tip, ~0.45 kg |
| 330104-00-20-05-02-00 | 3300 XL 8 mm Probe | 20 ft (6.10 m) | Armored | 8 mm tip, ~0.6 kg |
| 330104-00-05-10-02-00 | 3300 XL 8 mm Probe | 5 ft (1.52 m) | Non-armored | 8 mm tip, ~0.4 kg |
Popular Modèles from Bently Nevada Product Line
| Modèle | Product Type | Application Area | Dimensions & Poids |
|---|---|---|---|
| 3500/22M | Transient Data Interface Module | Machine Protection Systems | ~0.8 kg |
| 3500/42M | Proximitor/Seismic Monitor | Shaft vibration, bearing wear | ~1.2 kg |
| 3500/33 | RTD/TC Temperature Monitor | Motor winding / bearing temp | ~1.1 kg |
| 330130-040-00-00 | 3300 XL 8 mm Extension Cable | Drives matching probes | ~0.3 kg |
| 330180-50-00 | 3300 XL Proximitor Sensor | Drives 3300 XL 8 mm probes | ~0.5 kg |
| 3500/15 | Power Supply Module | 3500 Series Rack | ~1.5 kg |
Informations sur l'entreprise
E-mail: [email protected]
Mobile：Contactez-nous par email
Whatsapp：Contactez-nous par email
Add: Alishan Building, 2 Lvling Rd, District Siming, Xiamen, Fujian, Chine, 361006
Nos services
Nous sommes spécialisés dans la fourniture de pièces d'automatisation industrielle avec une garantie d'un an. Nos pièces d'automatisation industrielle sont vendues dans le monde entier.
Nous pouvons fournir des équipements et des pièces détachées de différents pays et fabricants, résoudre vos inquiétudes ou problèmes de qualité en de nombreux endroits, et surfrir un excellent avantage de prix.
N'hésitez pas à nous appeler pour plus de détails sur les produits.